Geotechnical Engineering Questions and Answers – Shear Strength of Cohesive Soil

Geotechnical Engineering Objective Questions

Civil Engineering MCQs

This set of Geotechnical Engineering Multiple Choice Questions & Answers (MCQs) focuses on “Shear Strength of Cohesive Soil”.

1. The un-drained test is carried out on sample of clay, silt, and peat to determine _____________

A) Shear Strength of natural ground and Sensitivity
B) Pore pressure
C) None of the mentioned
D) All of the mentioned

Answer is A)
Explanation: The un-drained test is carried out on undisturbed sample of clay, silt and peat to determine the strength of the natural ground and also carried out on remoulded samples of clay to measure it its sensitivity.

2. In an un-drained test on saturated clays, both σ1’ and σ3’ is independent of ____________

A) Pore pressure
B) Shear strength
C) Cell pressure
D) Effective pressure

Answer is C)
Explanation: In an un-drained test on saturated clays (B=1), both the major principal effective stress σ1’ and the minor principal effective stress σ3’ are independent of the magnitude of cell pressure applied.

3. The consolidated-un drained test can be performed in ___________ methods.

A) 3
B) 2
C) 4
D) 1

Answer is B)
Explanation: The consolidated-undrained tests are performed by two methods: i) the remoulded specimens are sheared under a cell pressure. ii) the moulded specimens are consolidated under the same cell pressure and sheared with different cell pressure.

4. Which of the following cannot be obtained by using un-drained test?

A) Effective stress failure envelope
B) Shear strength
C) sensitivity
D) All of the mentioned

Answer is A)
Explanation: Since only one Mohr circle in terms of effective stresses, is obtained from all un-drained tests, effective stress failure envelope cannot be obtained from this test.

5. The change in the pore pressure during an un-drained shear can be explained by ___________

A) Lateral pressure
B) Effective stress
C) Pore pressure parameter
D) Mohr’s circle

Answer is C)
Explanation: The change in the pore pressure due to change in the applied stress, during an un-drained, any be explained in terms of empirical coefficients called pore pressure parameters.

6. Factor affecting pore pressure parameters is ___________

A) Type of shear
B) Temperature
C) Nature of the fluid
D) All of the mentioned

Answer is D)
Explanation: Type of shear, sample disturbance, and environment during shear such as temperature and nature of the fluid are the factors that affect pore pressure parameter.

7. The value of pore pressure parameter, at failure for saturated clay is __________

A) 1.2 to 2.5
B) 2 to 3
C) 0.3 to 0.7
D) 0.7 to 1.3

Answer is B)
Explanation: The approximate value of pore pressure parameter at failure for very loose, fine saturated sand, saturated clays is 2 to 3.

8. Negative pore pressure in clay or sand is developed due to __________

A) Expansion on loading
B) Over loading
C) Loose structure
D) Compaction

Answer is A)
Explanation: A negative pore pressure is developed when we apply load on a sample of clay or sand because both sand and clay tends to expand on loading.

9. If the pore pressure is measured during un-drained stage of the test, the result can be expressed in terms of __________

A) C’ and φ
B) cu
C) None of the mentioned
D) All of the mentioned

Answer is A)
Explanation: Both effective parameters C’ and φ’ can be expressed when pore pressure is measured during un-drained stage of the test.

10. The equation for the unconsolidated un drainage strength of clay is __________

A) τ = c + σ tan φ
B) τ = c + σ tan φ
C) τ = c + σ
D) τ = σ tan φ

... Answer is B)
Explanation: The equation for consolidated undrained strength of the preconsolidated clay in terms of total stress can be approximately expressed as τf = ccu + σ tan φcu where, σ is the normal pressure.